F1 23 (PC) - Fanatec Recommended Settings
![Dominic Brennan](https://admin.forum.fanatec.com/uploads/userpics/174/n70FVJFNOWNG0.jpg)
General Notes:
- The settings below are considered to be reasonable baseline values for F1 23 (PC). They might not suit all tastes and driving styles, but they are a good starting point.
- In order to apply the suggested settings correctly, it is important to assign both the Tuning Menu values AND the suggested In-Game settings together.
- These settings assume you have updated all firmware from the latest Fanatec Driver package (available on the front page of the Fanatec website).
- If you cannot access all the settings shown below, you are probably in the Standard Tuning Menu. To switch to the Advanced Tuning Menu, first enter the menu (short-press the Tuning button once), then press and hold the Tuning button for about four seconds.
- You may see additional Tuning Menu settings depending on your connected devices. These additional settings are not relevant to force feedback, and are not listed here.
- The settings for the CSL DD / Gran Turismo DD Pro are suitable for 5 Nm and 8 Nm (Boost Kit 180).
- The settings for the Podium Wheel Bases assume you are in High Torque Mode. In Low Torque Mode, the same settings can be used, but with a higher FF value.
CSL DD / Gran Turismo DD Pro
Tuning Menu Settings:
- SEN Auto
- FF 100
- FFS Peak
- NDP 30
- NFR Off
- NIN Off
- INT 3
- FEI 100
- FOR 100
- SPR 100
- DPR 100
In-Game Settings:
- Vibration and Force Feedback: On
- Vibration & Force Feedback Strength: 65
- On Track Effects: 30
- Rumble Strip Effects: 40
- Off Track Effects 30
- Wheel Damper: 2
- Maximum Rotation (F1 & F2): 360
- Maximum Rotation (Supercars): 900
Podium Wheel Base DD1 / DD2 / Podium Racing Wheel F1
- SEN Auto
- FF 45
- FFS Peak
- NDP 15
- NFR Off
- NIN Off
- INT 3
- FEI 100
- FOR 100
- SPR 100
- DPR 100
In-Game Settings:
- Vibration and Force Feedback: On
- Vibration & Force Feedback Strength: 45
- On Track Effects: 30
- Rumble Strip Effects: 40
- Off Track Effects 30
- Wheel Damper: 2
- Maximum Rotation (F1 & F2): 360
- Maximum Rotation (Supercars): 900
ClubSport Wheel Base V2.5
- SEN Auto
- FF 100
- DRI -02
- FOR 100
- SPR 100
- DPR 100
- FEI 80
In-Game Settings:
- Vibration and Force Feedback: On
- Vibration & Force Feedback Strength: 65
- On Track Effects: 30
- Rumble Strip Effects: 40
- Off Track Effects 30
- Wheel Damper: 2
- Maximum Rotation (F1 & F2): 360
- Maximum Rotation (Supercars): 900
CSL Elite Wheel Base V1.1 / CSL Elite Wheel Base +
- SEN Auto
- FF 100
- DRI -02
- FOR 100
- SPR 100
- DPR 100
- FEI 60
In-Game Settings:
- Vibration and Force Feedback: On
- Vibration & Force Feedback Strength: 65
- On Track Effects: 30
- Rumble Strip Effects: 40
- Off Track Effects 30
- Wheel Damper: 2
- Maximum Rotation (F1 & F2): 360
- Maximum Rotation (Supercars): 900
Comments
Finally waited until it was released!😍
Much appreciated.. will test now.
Thank you.
Thanks for all the work!
Setup i use - CSL DD 8NM with Mclaren GT3 V2 wheel with metal QR.
Wheel feels very heavy with these settings, can barely turn it. Also in the menu in F123, the CSL DD wheel in combination with the Mclaren GT3 V2 wheel does not get immediately recognized. What seems to be enabled out of the box is a profile called - GT SW PRO RIM - requring a GT DD PRO. Also all the selections under settings are showing up as GT DD Pro and not CSL DD. This is with running the wheel in PC mode - red light.
Should I be using different settings, is there anything I am missing? Also the screen on the GT3 wheel does not seem to be working with F123 but here I need to test more.
Thank you.
For GT DD PRO, should we use PC MOD (red) or compatibility (Yellow) ? Thank in advance.
Red. Otherwise it would have been written in the recommended settings ;)
Okay thanks !
Anyone find 360 just too high? I feel like I wash out on a lot of corners
360 could be issue at multi reason, example you not using formel 1 steering wheel , in that case its probably better use the 240-270 instead
I have just got the CSL Ready to Race bundle and I have the same problem with the steering wheel profile is GT SW PRO RIM - requring a GT DD PRO.
I managed to configure in a separate profile but did you manage to find a way so it's says CSL DD?
Got the v1.1 + mclaren v2 wheel. for some reason i cant set dri to -2 only of 1,2 or 3. and can only change sen,ff mp( what ever that is) and dri. dont know what im diong wrong or wich settings to use. wheel feels to light compared with iracing.
You are in the Standard Tuning Menu with limited settings and limited value ranges.
To get all settings with extended value ranges you need to set the Tuning Menu to Advanced by pressing the Tuning Menu button for 3 seconds while being in the Tuning Menu.
Hi,
Do you have settings for the Clubsport DD on PC?
Hola, estos ajustes siguen siendo validos para f1 23 en 2024 CSL DD 5Nm? lo noto un poco raro, algún ajuste que lo mejore?
Configuration for the ClubSport DD+ or ClubSport DD??
How can I set ffs to peak? I don’t see ffs in the tuning menu of my dd+
CS DD does not have FFS setting because Peak and Linear are the same on these bases.