Sorry for all the no words post, had some trouble with the site earlier Anyway, followed 1-8 and it didn't change anything Even changing my 4K res 3840x2160 to 1080p didn't solve it either
Did you restart the PC after changing the resolution from Full 4k to 1080p???
at Full 4k 3280 x 2160 your test is sized to 200% you have to Restart/ Log Off and back on for the PC to apply the New scaling to text, Icons ETC....When i set Resolution to 1080p the Fanatec wheel properties page text is perfect after a restart.
Sorry for all the no words post, had some trouble with the site earlier Anyway, followed 1-8 and it didn't change anything Even changing my 4K res 3840x2160 to 1080p didn't solve it either
Did you restart the PC after changing the resolution from Full 4k to 1080p???
at Full 4k 3280 x 2160 your test is sized to 200% you have to Restart/ Log Off and back on for the PC for PC to apply the New scaling to text, Icons ETC....When i set Resolution to 1080p the Fanatec wheel properties page text is perfect after a restart.
Errrm! No I didn't...I will try this a little later..Right now I'm winning a bid on ebay10 mins left
Sorry for all the no words post, had some trouble with the site earlier Anyway, followed 1-8 and it didn't change anything Even changing my 4K res 3840x2160 to 1080p didn't solve it either
Did you restart the PC after changing the resolution from Full 4k to 1080p???
at Full 4k 3280 x 2160 your test is sized to 200% you have to Restart/ Log Off and back on for the PC to apply the New scaling to text, Icons ETC....When i set Resolution to 1080p the Fanatec wheel properties page text is perfect after a restart.
Yes it did work :)I had forgotten I set up a custom scaling for this monitor, as at 4K icons were too small I had 136% custom scale
I can’t upgrade to 662 firmware, requires Hex File
What hardware do you use?
Does it not work when you click on connect and then flash firmware? You should not have to select a hex file manually, if it puts out an error message, please send a screenshot.
When the ClubSport Steering Wheel Formula V2 EU is connected to DD1 and I start the Fanatec Driver on PC always come the question "This driver includes a new Clubsport... V2 firmware..." ´. After I press OK (or x) all Fanatec driver windows will be closed, The DD1 display is black and the wheel shows only the Fanatec F. Then the only thing that I can do is restart the DD1.
For those of you who still have DPI / resolution issues, are you using multiple screens? Can you send more information of your monitor setup and the settings you've chosen so we can try to replicate it.
The attached screenshot is what solved it for me once I had it, but I didn't use a custom scale or 4k.
Can you also try to check the first box in the upper part of your screenshot to see if it makes a difference and maybe uncheck the box you've selected right now.
For those of you who still have DPI / resolution issues, are you using multiple screens? Can you send more information of your monitor setup and the settings you've chosen so we can try to replicate it.
For those of you who still have DPI / resolution issues, are you using multiple screens? Can you send more information of your monitor setup and the settings you've chosen so we can try to replicate it.
Yes, I've got multiple screens.. But will try what Grimey says... To me it seemed obvious that it would've been applied after the press of Okay
Edit... The format change did happen, now that I've booted up my pc a day later. So after the 7th step, should 8 be: restart your pc and open the Fanatec app again. But it is annoying that I have to change that setting each time I install a new driver. Cause I'm downgrading my base, because I think I've got an oscillation issue with new fw. And I've got the same compressed text issue again.
Just got my DD1, Updated firmware... noproblem ... BUT when trying to update MOTOR FIRMWARE nothing happens ... DD goes black and software is reporting a "COM3" problem, will NOT upgrade from 29 to 30 ... Any one???
Just got my DD1, Updated firmware... noproblem ... BUT when trying to update MOTOR FIRMWARE nothing happens ... DD goes black and software is reporting a "COM3" problem, will NOT upgrade from 29 to 30 ... Any one???
Got it with the BMW rim, Porsche rim,McLaren rim, Formula V2 and the XUH So not a steering wheel related issue.
I've got a terrible oscillation problem since updating to latest fw. Normally I drive without any spring, damper, natural damper and friction forces activated, so all these are OFF. After updating to the fw shown above. I noticed it in AC: Alfa touring V6, Spa and no setup to the car. On the straights, the wheel began oscillating like crazy. So i had to set the natural damper up to 55% to minimize it to a doable point, but it still wasn't optimal.
So after AC I tried R3E and RF2...but all had the same issue.
So I just downgraded to Driver V340, base fw 358 and base motor fw 30 and the oscillation with the Alfa V6 is almost gone (like I'm used to) with this base fw. With dampers, spring etc set to OFF that is, ofcourse.
Has the drift menu changed for CSW2.5? It used to go from -5 to +5 but now it's off to +5, no minus values like the CSL. Is this a bug or you guys ditched the minus values for CSW2.5 too?
If so what is the natural value? Thanks in advance.
Restarted the wheel, it went back to normal, weird though.
I installed the 64 Bit version of the driver package. This firmware works fine for me. The wheel seems to be more responsive than with version 328 and motor driver 18. Gone is the coil whine when idling. That's good. The property page displayed correctly on m system. Didn't experienced any notchiness of the wheel.
The only issues I encountered are concerning the CSW RUHX:
- the calibration process can't be initialized anymore
- the white status LED on top of the wheel base stays dark when enterin the setup menu
- can't change the operation modes (xbox, ps, pc) anymore
(Neither of these issues are a problem for me, because the wheel is calibrated and I don't need to change the operation modes.)
On top of my personal whish for the driver is a substitute for DXTweak. Which does not work anymore since I installed the CS WB. It would be very helpful if you could integrate a function that allows to adjust the (pedal) axises within the property page of the driver similar to DXTweak. A bonus would be if you could save different profiles.
I can’t upgrade to 662 firmware, requires Hex File
What hardware do you use?
Does it not work when you click on connect and then flash firmware? You should not have to select a hex file manually, if it puts out an error message, please send a screenshot.
some pepole have this problom. I just like drive cannot find fw.hex with default file path.
maybe interference from other software , or wrong drive install path
I can’t upgrade to 662 firmware, requires Hex File
What hardware do you use?
Does it not work when you click on connect and then flash firmware? You should not have to select a hex file manually, if it puts out an error message, please send a screenshot.
some pepole have this problom. I just like drive cannot find fw.hex with default file path.
maybe interference from other software , or wrong drive install path
Which default file path? You only need to press connect and then flash firmware. You don't even have to search for a folder, just two clicks and then the firmware should be loaded.. A screenshot would definitely help in this case.
I can’t upgrade to 662 firmware, requires Hex File
What hardware do you use?
Does it not work when you click on connect and then flash firmware? You should not have to select a hex file manually, if it puts out an error message, please send a screenshot.
some pepole have this problom. I just like drive cannot find fw.hex with default file path.
maybe interference from other software , or wrong drive install path
Which default file path? You only need to press connect and then flash firmware. You don't even have to search for a folder, just two clicks and then the firmware should be loaded.. A screenshot would definitely help in this case.
Normal is supposed to be like this, but some people are not.
I can’t upgrade to 662 firmware, requires Hex File
What hardware do you use?
Does it not work when you click on connect and then flash firmware? You should not have to select a hex file manually, if it puts out an error message, please send a screenshot.
some pepole have this problom. I just like drive cannot find fw.hex with default file path.
maybe interference from other software , or wrong drive install path
Which default file path? You only need to press connect and then flash firmware. You don't even have to search for a folder, just two clicks and then the firmware should be loaded.. A screenshot would definitely help in this case.
Normal is supposed to be like this, but some people are not.
update soft told them cannot load .hex.
Are you following this procedure? Starting at 1:51 of the video
Just got my DD1, Updated firmware... noproblem ... BUT when trying to update MOTOR FIRMWARE nothing happens ... DD goes black and software is reporting a "COM3" problem, will NOT upgrade from 29 to 30 ... Any one???
If it also doesn't work with a different driver there might be an issue with the bootloader of the motor firmware, please contact support. You can also check if your tuning menu lists all adjustments like NDP and FEI for example, if something is missing there is no proper communication to the motor driver but only support can help you.
Got it with the BMW rim, Porsche rim,McLaren rim, Formula V2 and the XUH So not a steering wheel related issue.
I've got a terrible oscillation problem since updating to latest fw. Normally I drive without any spring, damper, natural damper and friction forces activated, so all these are OFF. After updating to the fw shown above. I noticed it in AC: Alfa touring V6, Spa and no setup to the car. On the straights, the wheel began oscillating like crazy. So i had to set the natural damper up to 55% to minimize it to a doable point, but it still wasn't optimal.
So after AC I tried R3E and RF2...but all had the same issue.
So I just downgraded to Driver V340, base fw 358 and base motor fw 30 and the oscillation with the Alfa V6 is almost gone (like I'm used to) with this base fw. With dampers, spring etc set to OFF that is, ofcourse.
So I'm passing on fw 662
What's your FFB strength on the base, in-game gain and FEI setting? Do you use the gyro setting in the ini file?
To me it doesn't make sense because there was no change in firmware which could lead to this and we haven't noticed anything like that.
It's also surprising to me that any older firmware can have no oscillations with these settings, because there is no dampening going on at all it's totally normal to oscillate.
I installed the 64 Bit version of the driver package. This firmware works fine for me. The wheel seems to be more responsive than with version 328 and motor driver 18. Gone is the coil whine when idling. That's good. The property page displayed correctly on m system. Didn't experienced any notchiness of the wheel.
The only issues I encountered are concerning the CSW RUHX:
- the calibration process can't be initialized anymore
- the white status LED on top of the wheel base stays dark when enterin the setup menu
- can't change the operation modes (xbox, ps, pc) anymore
(Neither of these issues are a problem for me, because the wheel is calibrated and I don't need to change the operation modes.)
On top of my personal whish for the driver is a substitute for DXTweak. Which does not work anymore since I installed the CS WB. It would be very helpful if you could integrate a function that allows to adjust the (pedal) axises within the property page of the driver similar to DXTweak. A bonus would be if you could save different profiles.
Do you try to switch modes using the button clusters or the fixed buttons on top of the UHX where the display is?
Comments
Errrm! No I didn't...I will try this a little later..Right now I'm winning a bid on ebay10 mins left
PC driver: 344
Wheel Base Firmware: 662
SW FW: 27
Wheel Base Motor 30
WHEEL BASE 662
MOT CON 30
ST WHEEL 27
What can I do?